Power Generators: Starter Batteries

OGi Bloc Batteries
(according to VDE 0100 part 710 & 7108 according to DIN 6280 Teil 13 – formerly VDE 0107/0108)

Emergency starter batteries supply the starter with energy. These are so-called OGi (surface-lead batteries), which are prescribed according to VDE 0100 part 710/0108. The starting current for the starter is provided by OGi Bloc starter batteries. These also ensure that the most important monitoring functions of the power generator remain active even in a voltage-free state.

The WA Notstromtechnik GmbH OGi bloc batteries are sturdy, optimized  for high discharge power lead-acid batteries, particularly suitable for bridging times of a few seconds up to one hour.

They are used as starter batteries for uninterruptible power supplies (UPS) of emergency generators, auxiliary power supply of data and signal systems of transport systems, switchgears of utilities and other equipment.

We can assist with the battery selection.

Battery types, capacities, dimensions, mass

Battery Type C10 C3
UE V / cell 1,80 Ah 1,75 Ah
12 V 1 OGi 25 38 Ah 26,50 Ah
12 V 2 OGi 50 54 Ah 45 Ah
12 V 3 OGi 75 79 Ah 63 Ah
12 V 4 OGi 100 105 Ah 81 Ah
12 V 5 OGi 125 135 Ah 105 Ah
12 V 6 OGi 150 165 Ah 129 Ah
6 V 7 OGi 175 190 Ah 151 Ah

 

Battery Type C1 C 1/2
UE V / cell 1,70 Ah 1,65 Ah
12 V 1 OGi 25 20,50 Ah 16,50 Ah
12 V 2 OGi 50 35 Ah 28,50 Ah
12 V 3 OGi 75 50 Ah 41 Ah
12 V 4 OGi 100 65 Ah 53,50 Ah
12 V 5 OGi 125 78 Ah 68 Ah
12 V 6 OGi 150 92 Ah 83 Ah
6 V 7 OGi 175 106 Ah 98 Ah

 

 Battery Type RI 1 IK 2
UE V / cell  –
12 V 1 OGi 25 16,80 mW 0,73 kA
12 V 2 OGi 50 8,40 mW 1,46 kA
12 V 3 OGi 75 5,60 mW 2,20 kA
12 V 4 OGi 100 4,20 mW 2,93 kA
12 V 5 OGi 125 3,36 mW 3,66 kA
12 V 6 OGi 150 2,80 mW 4,39 kA
6 V 7 OGi 175 1,20 mW 5,13 kA

 

 Battery Type Length Width
UE V / cell
12 V 1 OGi 25 272 mm 205 mm
12 V 2 OGi 50 272 mm 205 mm
12 V 3 OGi 75 272 mm 205 mm
12 V 4 OGIi 100 272 mm 205 mm
12 V 5 OGi 125 380 mm 205 mm
12 V 6 OGi 150 380 mm 205 mm
6 V 7 OGi 175 272 mm 205 mm

 

 Battery Type Height max. Mass 3
UE V / cell
12 V 1 OGi 25 385 mm 22 kg
12 V 2 OGi 50 385 mm 30,1 kg
12 V 3 OGi 75 385 mm 38,2 kg
12 V 4 OGi 100 385 mm 47,3 kg
12 V 5 OGi 125 385 mm 62,3 kg
12 V 6 OGi 150 385 mm 70,5 kg
6 V 7 OGi 175 385 mm 37,7 kg

 

Battery Type Mass 4
UE V / cell  –
12 V 1 OGi 25  33 kg
12 V 2 OGi 50  41 kg
12 V 3 OGi 75  49 kg
12 V 4 OGi 100  58 kg
12 V 5 OGi 125  78 kg
12 V 6 OGi 150  86 kg
6 V 7 OGi 175  49 kg

Construction

Positive electrode
Round grid plate with circular bars in a corrosion-res PbSb1, 6SnSe-alloy
Negative electrode
Grid plate in a low antimony alloy
Separation Microporous separator
Electrolyte Sulfuric acid of 1,24 kg/l
Vessel Transparent SAN (styrene-acrylonitrile), impact
Cover SAN dyed gray
Blocks with blind cells
4V, 6V, 8V, 10V
Plugs Labyrinth plugs for arresting aerosol, optional ceramic plugs or ceramic funnel plugs according to DIN 40 740
Pole bushing
100% gas- and electrolyte-tight, slidepole
Pole execution
M10 brass inlay
Connector Flexible insulated Copper cables with cross-selections of 35, 50, 70, 95 or 120 mm²
Protection IP 25 according to DIN 40050, touch protected according to VBG 4


Electric load

IU – Characteristic curve
Imax without limitation possible
U = 2,23 V/cell +- 1%, between 10°C and  55°C
D U/D T = -0,004 V/K below 10°C in the monthly average
Boost charge U = 2,35 to 2,40V/cell, limited in time
Loading time to 92% 6 h discharched 1,5*I10 initial current , 2.23 V/cell, 50% C10 discharched


Discharge

Referencetemperature 20°C
Initial capacity 100%
Discharge depth Normal to 80%
Discharge depth Discharge of more than 80% and discharges through the current-dependent discharge voltage should be avoided


Maintenance

All 6 month Battery voltage, check pilot block voltages and temperatures
All 12 month Monitor battery voltage, block voltages and temperatures

Operating Characteristics

Life utility >15 years at 20°C >7,5 years at 30°C >4 years at 40°C
Water refil interval
More than 3 years
IEC 896-1 Cycle
1.000
Self-discharge Approximately 3% per month at 20°C
Operating temperature -20°C to 55°C  recommended 10°C to 30°C
Aeration specification f1=0,5 (low antimony alloy) in accordance with VDE 0510 part 2
Dimensions DIN 40 737 part 3
Control IEC 896-1
Saftety standard VDE 0510, part 2
Transport No dangerous goods for road transport